Yale HSA3000 Dokumentacja Pobierz pdf (Strona 11)

Siren

The siren will produce a series of pips and ashes

when arming and disarming the system when

the batteries start getting low. After the warning

the batteries will have about enough energy for 1

month’s normal operation before exhaustion.

1 Switch off tamper protection as described in

section 5, table 1 & 2.

The batteries are changed as follows:

2 Remove the siren lid and switch off the siren

power.

3 Unscrew the four screws on the battery

compartment lid and remove.

4 Remove the four batteries and replace them with

four fresh alkaline “D” cells.

5 Switch on siren power and check that the siren

beeps and ashes.

Note After the batteries have been changed

and system powered on, the tamper will become

inactive for 3 hours to allow ﬁtting.

6 Replace battery compartment lid and screws

and reattach siren lid. Tamper protection would

automatically enabled when the 3 hours period

expired.

• Disarming under tamper condition causes the LED

to ﬂash sequentially for 2 cycles instead of 1 cycle

under normal condition.

PIR

When the battery is low the LED will ash when any

movement is detected. The batteries are changed

as follows:

1 Switch off tamper protection as described in

section 5, table 1 & 2.

2 Loosen the case screw and remove PIR sensor

from base to reveal three AAA batteries.

3 Press the learn button to drain residue power.

4 Insert new alkaline batteries observing correct

polarity.

5 Reﬁt sensor on base and tighten bottom case

screw. Switch tamper protection back on.

• PIR case tamper conditions are also indicated by

a ﬂashing LED, check the tamper before changing

the batteries.

Door/window sensor

When the battery is low the LED will lights up when

the door/window is opened or when tamper is

triggered. The battery is changed as follows:

1 Switch off tamper protection as described in

section 5, table 1 & 2.

2 Loosen the case screw and remove door/window

sensor from base to reveal battery.

3 Using a screwdriver gently lever out the old

battery.

4 Insert new CR2032 coin cell with the + side

uppermost.

5 Press battery into holder ﬁrmly with ﬁnger and

thumb until a click is heard.

6 Reﬁt sensor on base and tighten bottom case

screw. Switch tamper protection back on.

• Door/window sensor case tamper conditions are

also indicated by a ashing LED, check the tamper

before changing the battery.

Keyfob

When the battery is low the LED will glow dimly

when any key is pressed. The battery is changed as

follows:

1 Using a coin turn the battery cover anticlockwise

to the unlocked position and remove cover and

battery.

2 Insert new CR2032 coin cell with the + side

uppermost.

3 Replace battery cover.

4 Press any key and check that the LED lights.

If the LED lights the new battery installation is

successful.

Keypad

Note: Disable siren tamper before proceeding (Page

9, table 1)

When the battery is low the LED will ash when any

key is pressed. The battery is changed as follows:

1 Unscrew the two keypad case screws and remove

keypad back to reveal battery. Using a screwdriver

gently lever out the old battery.

2 Insert new CR2032 coin cell with the + side

uppermost.

3 Slide battery into holder. Please note the + contact

pin must stay above the battery.

4 Press a number key and check that the LED lights.

If the LED lights the new battery installation is

successful, screw keypad back on and the battery

change is complete.

Smoke Detector

The LED will ash and the sounder will beep every

30 seconds to signal low battery. Change the

batteries as soon as possible with fresh AA alkaline

replacements.

Help Button

Remove the cover by loosening the ﬁxing screw and

insert a new CR2032 battery.

Changing the batteries

Always use alkaline batteries or the correct type of coin cells as replacements because any other

battery can cause problems with the operation of the system. Typical life of batteries is two

years. Ensure the correct steps are taken when changing batteries in tamper protected devices.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Komentarze do niniejszej Instrukcji

Brak uwag

Yale HSA3000 Dokumentacja Strona 11

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Yale HSA3000